YOKOGAWA AQ1215A User Manual Download

Page: 59 / 282

2-21

IM AQ1210-01EN

Setting Up the OTDR Feature

App

Index

• When Event Fix Mode Is Set to Mode1

Events detected at positions other than the master event positions are also displayed in the

event list.

Events other than fixed events

are also detected.

An earlier event is detected, so the

number of this fixed event is updated

(changes from 3 to 4).

• When Event Fix Mode Is Set to Mode2

Only the events that are detected at the master event positions are displayed in the event list.

Not detected even when an event exists.

Zoom Direction

You can select the zoom behavior of the waveform display that is controlled with the arrow keys.

• Natural

The waveform is zoomed.

Zooms in vertically

Zooms out vertically

Zooms in horizontally

Zooms out horizontally

• Legacy

The waveform display range is zoomed. For example, if you expand the waveform display range

to the entire waveform, the displayed waveform will appear smaller. If you reduce the waveform
display range to a portion of the waveform, the displayed waveform will appear larger.

Zooms in vertically

Zooms out vertically

Zooms in horizontally

Zooms out horizontally

2.3 Display (OTDR) Conditions

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands