YOKOGAWA AQ1215A User Manual Download Page 234

Page: 234 / 282

9-7

IM AQ1210-01EN

Managing Data

App

Index

Loading Data (excluding system settings)

Tap the

File

icon to display the data management buttons.

Tap

LOAD

. A file list screen for loading data appears.

Tap an SOR file to select it.

Execute the data load operation. A feature starts according to the content of the file.

File List Screen for Loading Data

Set the file list display method (list, detail).

: List
: Detail

Displays the contents of the next higher level folder

File path

List of files and folders

Loads data

Sorts the file list

Note

• The instrument can load SOR files (waveform data) and CFG files (configuration data). Data in SOX,

BMP, JPG, or PDF format cannot be loaded.

• You cannot use this when the power meter logging feature is in use.

Loading the System Setup Data (CFG format)

Press

MENU

to display the MENU screen.

On the data management button window, tap

LOAD

. A file list screen for loading data appears.

The file the screen is the same as the one shown above.

Tap a CFG file to select it.

Execute the data load operation. The system settings are loaded.

9.4 Saving and Loading Data

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands