YOKOGAWA AQ1215A User Manual Download

Page: 125 / 282

6-17

IM AQ1210-01EN

Analyzing W

aveforms

App

Index

6.3 Displaying a Reference Trace

Procedure

Waveform Data Display

Press

MENU

to display the MENU screen.

For details on the MENU screen, see the Getting Started Guide, IM AQ1210-02EN.

Tap

OTDR

to display the OTDR screen.

• Switching the Display between TRACE Mode and MAP Mode

Tap the

TRACE

MAP

button to set the data display screen to TRACE mode.

When the data display screen is in TRACE mode, the button is MAP.

Displaying the Reference Source Waveform

Perform a measurement or load a file to display a waveform on the screen.

When performing an averaged measurement, wait for the measurement to complete. When loading a
waveform data file, use an SOR file that has been measured and saved with the instrument.

If you performed a measurement, display the waveform on the screen, and then end the

measurement.

Soft Key Menu (Snapshot)

Tap the soft key menu display button.

A soft key menu that can be used when real-time measurement or averaged measurement is not in
progress is displayed.

Soft key menu

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands