YOKOGAWA AQ1215A User Manual Download

Page: 213 / 282

8-42

IM AQ1210-01EN

Adjusting the Optical Power

Before starting the multicore loss test, directly connect the OTDR port (PORT1) on the slave

side of the instrument to the OPM port with a short optical fiber cable.

AQ1210A, AQ1215A,

AQ1210E, AQ1215E,

AQ1215F, AQ1216F

Light source

Optical power meter

Optical fiber cable under loss test

OTDR port (PORT1)

OPM port

Tap

LS Power Adjust

to display the following screen.

Starts optical power

adjustment

The measurement light

turns on.

When adjustment ends

normally, the instrument

returns to the previous

screen.

8.4 Performing a Multicore Loss Test (Multicore Loss Test)

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands