YOKOGAWA AQ1215A User Manual Download Page 225

Page: 225 / 282

8-54

IM AQ1210-01EN

Differential Trace Menu

Load analysis waveforms.

Selects the current trace (Trace A, TraceB, Diff.)

Select the waveform to place 4 Point Monitor markers and cursors on.

4 Point Monitor

Loss values can be measured for TraceA, TraceB, and differential trace.

• Loading Analysis Waveforms

Clears the waveforms of Trace1 to Trace2

When tapped, a file operation screen appears, and

you can load waveforms. See section 9.4.

• 4 Point Monitor

This is an example of placing 4 Point Monitor markers on the differential (Diff.) trace.

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Clears the marker

display

Place markers and for

monitoring the differential trace.

8.5 Performing Advanced Analysis (Advanced Analysis)

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands