YASKAWA CR700, Technical Manual, Page: 544 / 886

10.16 U: Monitors
544 YASKAWA SIEPC71061723A YASKAWA AC Drive CR700 Technical Manual
No.
(Hex.)
Name Description MFAO Signal Level
U3-11
(0094)
ElapsedTime@1stFault
Shows the cumulative operation time when the most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
No signal output available
U3-12
(0095)
ElapsedTime@2ndFault
Shows the cumulative operation time when the second most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
No signal output available
U3-13
(0096)
ElapsedTime@3rdFault
Shows the cumulative operation time when the third most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
No signal output available
U3-14
(0097)
ElapsedTime@4thFault
Shows the cumulative operation time when the fourth most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
No signal output available
U3-15
(080E)
ElapsedTime@5thFault
Shows the cumulative operation time when the fifth most recent fault occurred.
Unit: 1 h
No signal output available
U3-16
(080F)
ElapsedTime@6thFault
Shows the cumulative operation time when the sixth most recent fault occurred.
Unit: 1 h
No signal output available
U3-17
(0810)
ElapsedTime@7thFault
Shows the cumulative operation time when the seventh most recent fault occurred.
Unit: 1 h
No signal output available
U3-18
(0811)
ElapsedTime@8thFault
Shows the cumulative operation time when the eighth most recent fault occurred.
Unit: 1 h
No signal output available
U3-19
(0812)
ElapsedTime@9thFault
Shows the cumulative operation time when the ninth most recent fault occurred.
Unit: 1 h
No signal output available
U3-20
(0813)
ElapsedTime@10 Fault
Shows the cumulative operation time when the tenth most recent fault occurred.
Unit: 1 h
No signal output available
◆
U4: Maintenance Monitors
No.
(Hex.)
Name Description MFAO Signal Level
U4-01
(004C)
Cumulative Ope Time
Shows the cumulative operation time of the drive.
Use parameter
o4-01 [Elapsed Operating Time Setting] to reset this monitor. Use parameter o4-02
[Elapsed Operating Time Selection] to select the cumulative operation times from:
• The time from when the drive is energized until it is de-energized.
• The time at which the Run command is turned ON.
The maximum value that the monitor will show is 99999 . After this value is more than 99999 , the
drive automatically resets it and starts to count from 0 again.
Unit: 1 h
Note:
The MEMOBUS/Modbus communication data is shown in 10 h units. Use register 0099H for
data in 1 h units.
10 V: 99999 h
U4-02
(0075)
Num of Run Commands
Shows how many times that the drive has received a Run command.
Use parameter
o4-13 [RUN Command Counter @ Initialize] to reset this monitor. The maximum
value that the monitor will show is 65535 . After this value is more than 65535 , the drive
automatically resets it and starts to count from
0
again.
Unit: 1
10 V: 65535 times
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV
V/f CL-V/f OLV CLV AOLV