Xerox WC PE120 Series User Manual Download Page 39

Page: 39 / 283

Getting Started

2.13

Using a Parallel Cable

OTE

: Connecting the machine to the parallel port of the

computer requires a certified parallel cable. You need to buy an

IEEE-1284 compliant parallel cable that is 3 m or less in length.

Make sure that both the machine and the computer are
turned off.

Connect the parallel cable to the parallel connector on your
machine.

Push the metal clips down to fit inside the notches on the

cable plug.

Connect the other end of the cable to the parallel interface
port on your computer, and tighten the screws.

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands