Xerox WC PE120 Series User Manual Download Page 185

Page: 185 / 283

Troubleshooting

9.5

Clearing Paper Jams

When a paper jam occurs, “Paper Jam” appears on the display.

Refer to the table below to locate and clear the paper jam.

To avoid tearing the paper, pull out the jammed paper gently

and slowly. Follow the instructions in the following sections to

clear the jam.

In Tray 1

Open and close the front door. The jammed paper
automatically exits the machine.

If the paper does not exit, continue to step 2.

Pull Tray 1 open.

Message

Location of Jam

Go to

[Paper Jam 0]

Open/Close Door

In the paper tray

(Tray 1 or Tray 2)

below and

page 9.7

[Paper Jam 1]

Open/Close Door

In the fuser area or

around the toner

cartridge.

page 9.8

[Paper Jam 2]

Check Inside

In the paper exit area

page 9.9

Bypass Jam

In the Bypass tray

page 9.11

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands