Xerox WC PE120 Series User Manual Download Page 204

Page: 204 / 283

Troubleshooting

9.24

Page skew

• Ensure that the paper is loaded properly.
• Check the paper type and quality. See “Paper

Specifications” on page E.6.

• Ensure that the paper or other material is loaded correctly

and the guides are not too tight or too loose against the

paper stack.

• Try feeding paper through a different paper supply.

Curl or wave

• Ensure that the paper is loaded properly.
• Check the paper type and quality. Both high temperature

and humidity can cause paper curl. See “Paper

Specifications” on page E.6.

• Turn over the stack of paper in the paper tray. Also try

rotating the paper 180° in the tray.

• Try printing to the rear output slot.

Wrinkles or

creases

• Ensure that the paper is loaded properly.
• Check the paper type and quality. See “Paper

Specifications” on page E.6.

• Turn over the stack of paper in the paper tray. Also try

rotating the paper 180° in the tray.

• Try printing to the rear output slot.

Back of printouts

are dirty

Check for leaking toner. Clean the inside of the machine. See

“Cleaning the Inside” on page 8.3.

Black pages

• The toner cartridge may not be installed properly. Remove

the cartridge and reinsert it.

• The toner cartridge may be defective and need replacing.

Remove the toner cartridge and install a new one. See

“Replacing the Toner Cartridge” on page 8.8.

• The machine may require repair. Contact a service

representative.

Condition

Suggested solutions

AaBbCc

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands