Xerox WC PE120 Series User Manual Download Page 134

Page: 134 / 283

Faxing

7.8

Place the document

face down

on the document glass and

align it with the registration guide at the top left corner of

the glass.

OTE

: Make sure that no other documents are in the ADF

(Automatic Document Feeder). If a document is detected in the

ADF, the machine gives it priority over the document on the

document glass.

Close the document cover.

OTES

• If you are copying a page from a book or magazine, lift the cover

until its hinges are caught by the stopper and then close the

cover. If the book or magazine is thicker than 30 mm, start

copying with the cover open.

• To get the best scan quality, especially for colored or gray-scaled

images, use the document glass.

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands