Xerox WC PE120 Series User Manual Download Page 33

Page: 33 / 283

Getting Started

2.7

Loading Paper

The paper tray can hold a maximum of 250 sheets of 20 lb

(75 g/m

) plain paper.

To load a stack of Letter-sized paper:

Pull open the paper tray and remove it from the machine.

OTE

: If you want to load a different sized paper, you need to

adjust the paper guides. For details, see page 2.9.

Fan the edges of the paper stack to separate the pages.
Then tap the stack on a flat surface to even it up.

Insert the paper stack into the paper tray

with the side to

be printed on facing down

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands