Xerox WC PE120 Series User Manual Download Page 53

Page: 53 / 283

Getting Started

2.27

You can set the length of time for which the scan lamp waits

after a scan job is completed before it switches to the power

save mode.

Press

Menu

until “Machine Setup” appears on top line of

the display.

Press the scroll button (

) until “Scan PWR Save”

appears on the bottom line. Press

Enter

Press the scroll button (

) until the time setting you

want appears on the bottom line.

The available time options are 0.5, 1, 4, 8, and 12 (hours).

Press

Enter

to save the selection.

To return to Standby mode, press

Stop/Clear

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands