Xerox WC PE120 Series User Manual Download Page 31

Page: 31 / 283

Getting Started

2.5

Installing the Toner Cartridge

Open the front door.

Remove the starter toner cartridge from its bag. Gently
shake the cartridge 5 or 6 times to distribute the toner.

Thoroughly shaking the cartridge will assure maximum

copies per cartridge.

OTE

If toner gets on your clothing, wipe it off with a dry cloth

and wash clothing in cold water. Hot water sets toner into fabric.

AUTIONS

• To prevent damage, do not expose the toner cartridge to light for

more than a few minutes. Cover it with a piece of paper, if left

exposed for more than a few minutes.

• Do not touch the green underside of the toner cartridge. Use the

handle on the cartridge to avoid touching this area.

Summary of Contents for WC PE120 Series




























































































































































































































































































Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands

Xerox WC PE120 Series, User Manual

Search results

Summary of Contents for WC PE120 Series

Reviews:

Related manuals for WC PE120 Series

Brands by name

Popular brands