Volvo SDLG LG936L Operation & Maintenance Manual Download Page 99

Page: 99 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

△

WARNING

If the temperature of the gearbox oil is relatively highs please wear

protective clothes, and operate carefully to prevent injury.

Drain all the oil out and clean the oil on the draining plug and the oil on shell of the gearbox.

Wrap the plug with new ptfe tape and fit it well.

Loosen the oil inlet cover on the right side of the gear box which is on the right joint. Inject the

new hydraulic transmission oil.

Start the engine and run in the idle status. Check the oil level again.

△

NOTICE

If the old oil is dirty, do not add new oil directly.

Disassemble the raw oil filter which is in profile, and clean all the parts.

If there are any metal powders or fragments please contact the

maintenance man.

Assemble the parts, and add a little new hydraulic transmission oil. Start

engine and hold in the idle status for 3~5 minutes. Release the oil in the

oil pan and add new oil.

3.6.4 Adding Oil to Axle

Oil Level Check

①

Park the machine on level ground and put the

transmission lever in the

neutral

position. Pull

the parking brake switch, and wedge the front tire.

Loosen the oil inlet plug on the shells of the front

and rear axles. It is proper if the oil level is at the

bottom side of the oil inlet, otherwise please add

axle oil. Please watch for 5 minutes after adding

oil. If the oil level keeps stable, please assemble

the plug. For selections of axle oil, please refer to

CHAPTER IV 2.2

Selection of Oil,

Fuel and Coolant.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands