Volvo SDLG LG936L Operation & Maintenance Manual Download Page 77

Page: 77 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

Start the engine.

Open the air volume and power

switch 2 which have three gears (fan

low gear, fan middle gear and fan

high gear) and four positions (O, L,

M and H). The speed of evaporating

fan increases from left to right to

adjust the air volume.

Open the temperature control switch

3 to the max (the indicator lamp1 will

light), then the compressor starts working for the refrigeration of air conditioning.

Turn the air volume and power switch 2 to select different gear to obtain three different

volume of air.

Turn the temperature control switch anticlockwise slowly to obtain the desired temperature

until the indicator lamp 1 turns off and the compressor stops working. Now the setting

temperature is the temperature in the cab. When the inside temperature is higher than the

setting temperature, the indicator lamp 1 lightens and the compressor will begin to refrigerate;

when the inside temperature is lower than the setting temperature, the indicator lamp 1 turns

off and the compressor stops working.

b) Heating

Before using, turn the temperature control switch to the ‘O’ position (the state of off).

Open the hot water valve and start engine.

Open the air volume and power switch 2 to choose the position of gear and adjust to the

desired air volume.

1.2.9.2

Ⅱ

control panel and is operation (if assembled)

The Appearance of Panel

1. Working Indicator Lamp
2. Air Volume and Power Switch

3. The Switch to Control the Temperature

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands