Volvo SDLG LG936L Operation & Maintenance Manual Download Page 97

Page: 97 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

Lay back the dipstick, close the side door on the cover of engine. For choosing the appropriate oil

please refer to

CHAPTER IV 2.2 Oil Selection

Engine Oil Replac

②

ement

Park the machine on level ground, and put the transmission lever in

neutral

position. Pull the

parking brake switch and put the blocks in the front and back of the tires. Start the engine and run

at idle status until the oil temperature reaches 20

℃

～

40 , then stop the engine.

℃

Rotate the oil drain plug and let the oil flow out

and hold it in a container.

After the oil is released completely, rotate the oil

drain plug back and open the right side door of

engine cover; add prescribed engine oil (about

12L) from oil inlet of engine. Run the engine at

idle status, check whether the oil filter and oil

releasing plug are leaky.

After the engine was stopped for 15 minutes, let

the engine oil flow back to the oil pan, and check

the engine oil level of the engine again.

Engine oil Filter Replac

③

ement

Clean the area near the engine oil filter. Disassemble it with filter elements spanner.

Assemble

Add diesel oil full in the filter element and smear engine oil on the rubber seal ring.

Tighten 3/4~1 cycles after the seal ring connects with the base.

Start the engine and check whether the seal ring is seal. If not, disassemble the filter element and

check the sealing surface.

△

NOTICE

After changing the filter elements, the engine must run in the idle

status at least 1 minute to ensure the engine is lubricated

sufficiently before working.

Over tight mechanical rotation could damage the screw thread or

filter element sealing.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands