Volvo SDLG LG936L Operation & Maintenance Manual Download Page 113

Page: 113 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

103

Remember to wipe off the overflow lubricant when adding it.

2.1.4 The Storage of Oil and Fuel

Prevent water, dirt or other impurities from mixing with the oil.

Follow the rule, first in first out, to maintain oil quality during long-term storage (Use the oil with

the longest shell life).

2.1.5 Filters

Filters are extremely important safety components. They can prevent impurities in the fuel from

entering important equipment and causing problems. Replace all filters periodically. For the

maintenance cycle, refer to

3. CONTENT OF MAINTENANCE, in this chapter

. Replace

filters at shorter intervals when the machine works in a severely bad environment.

Never

try to clean paper filter elements and use them again.

Always

replace them with a new

one.

When replacing the oil filters, check whether there are some metallic particles adhering to the old

filter. If some metal particles are found, consult the maintenance people.

Never

open the packs of new filters until they are used.

Always

use authorized filter parts.

2.2 Selection of Fuel, Coolant and Lubricant

2.2.1 Selection Table of Fuel, Coolant and Lubricant

Please choose Shandong Lingong’s preferred special oils and choose specified oils from the following

table.

Kinds of

Fluids

Recommended Types And Standards

Capacity

Using places

Ambient temperature

≥

-15°

CD 15W-40 Diesel Oil GB11122

17L

Yuchai Engine

Ambient temperature<-15°

CD 5W-30 Diesel Oil GB11122

13.3L

Weichai Engine

Engine oil

CALTEX & GINDERLEGR engine oil 15W-40

12L

Cummins Engine

transmit oil

Q/SH303 064

45L

Transmit

oil

transmit oil

Q/SH303 064

45L

Torque converter and

gearbox

Gear oil

Heavy duty gear oil for automobile (GL-5) 85W-90 GB13895 2×13L

Main reducer and final

drive

Ambient temperature

≥

-5° L-HM46 hydraulic oil GB11118.1

Ambient temperature

≥

-10°L-HM32 hydraulic oil GB11118.1

Ambient temperature

≥

-30°L-HV46 hydraulic oil GB11118.1

128L

Hydraulic oil tank

(Domestic Type)

Hydraulic

oil

CALTEX superfine wind ring of temperature anti-grinding
hydraulic oil or MOBIL DTE25

128L

Hydraulic oil tank

(Export Type)

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands