Volvo SDLG LG936L Operation & Maintenance Manual Download Page 8

Page: 8 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

VIII

PREFACE

Thank you for purchasing the wheel loader produced by Shandong Lingong.

This manual is a guideline for users to operate and maintain this machine properly. Keep this manual

within easy access and have all relevant people read it before use. If this manual is lost, damaged or

cannot be read, contact our company or our dealers.

If you sell the machine, be sure to give this manual to the new owners.

Parameters, figures and information included in this manual apply only to basic loaders. For those

derivative products, please consult us or refer to the relative manuals.

When selecting working equipment, please follow the user manual of the working equipment to

assemble and disassemble, replace and use.

In addition, please read carefully the attached technical user manual for the diesel engine and other

functioning parts about operation, use and maintenance.

We are continually striving to improve the quality of our products, to produce more advanced and a

safer engineering machine. We reserve the right, at our sole discretion, to change or modify our

design, but we do not promise to apply the changes to products that are sold. We also reserve the right

to change the data and machine, and the right to maintain it. The design, operation and user

information in this document is subject to change without notice. Customer feedback is very

welcomed. If you would like to comment on any aspect of this manual or our products in general,

please feel free to contact us.

Please give us feed back about the shortcomings immediately upon using our products, so that we can

continue to improve our products to satisfy your requirements.

All rights are reserved. The contents of this publication may not be reproduced in any form, or

communicated to a third party without prior written permission of Shandong Lingong Construction

Machinery Co. Ltd.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands