Volvo SDLG LG936L Operation & Maintenance Manual Download Page 98

Page: 98 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

3.6.2 Adding Fuel to Fuel

Tank

Fuel Level Check

Park the machine on level

ground, and check the fuel level

by dipstick on the outside of fuel

tank.

If the fuel level is under 0,

please add fuel from inlet on the

fuel tank. For fuel selection

please refer to

CHAPTER IV 2.2 Selection of Oil, Fuel and Coolant

3.6.3 Adding Oil to Gearbox

Oil Level Check

①

Park the machine on level ground and put the transmission

lever in the

neutral

(“

”) position. Pull the parking brake

switch, and wedge the front tire.

Start engine and let the engine run in the idle status for

minutes. Open the checking plug on the right of the gear box.

If some oil flow out without pressure, the oil is of proper

volume. If the oil level is lower than the plug, hydraulic

transmission oil should be added. The choice of the

hydraulic transmission oil can be found in

CHAPTER IV

2.2 Selection of Oil, Fuel and Coolant

New Oil Replac

②

ement

Park the machine on level ground and put the transmission

lever in the

neutral

(“

”) position. Push the parking

brake switch, and wedge the front tire.

Start engine and let the engine run in the idle status for

minutes, then stop the engine. Loosen the oil drain plug

on the bottom right of the gearbox to drain the oil, and

contain it with container.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands