Volvo SDLG LG936L Operation & Maintenance Manual Download Page 101

Page: 101 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

CHAPTER IV 2.2

Selection of Oil, Fuel and Coolant

for selection of oil..

Oil Replac

②

ement

△

WARNING

While replacing oil if other maintenance needs to be done do

so following the relevant rules, and pay attention to safety.

△

NOTICE

Pay attention to the clarity of the oil while replacing it;

never

let other materials enter the hydraulic system directly.

Clean out the in bucket. Park the machine on level ground and put the transmission lever in the

neutral

position. Pull the braking control lever. Start the engine and keep in the idle status for 10

minutes. Raise and lower the lift arm several times, and tilt the bucket forward and backward

several times.

Raise the lift arm to the highest position; tilt the bucket backwards to the extreme position and

shut the engine.

Push the bucket control lever forward to let the bucket tilt forward freely by its weight. Drain out

the oil in the bucket cylinder. After the bucket has tilted to the desired position, push the lift arm

control lever forward to let the lift arm fall down by its weight freely. Drain out the oil in the lift

arm cylinder.

Loosen the oil releasing spherical valve on the oil tank bottom to drain the oil to the container.

Open the oil inlet cover at the same time to hasten the draining process.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands