Volvo SDLG LG936L Operation & Maintenance Manual Download Page 75

Page: 75 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

1.2.5 Cab Door Locking Bar

Outside Cab Locking Bar:

Open the left and right door to 180° and the orientation lock on the door

will touch the outside lock of the cab and the door will be locked outside the cab. Turn the control bar

downward and it will unlock.

Inside Cab Locking Bar:

When the lock of the

cab is in the locked positions, the door will be

locked automatically after closing the door. Insert

key outside the cab. Turn 180°clockwise and pull

out key. Pull the handle outside the cab and the

cab door will open. Turn the lock bar upward and it will open.

1.2.6 Frame Locking Bar

△

! WARNING

Be sure to use the front and rear frame locking bar during

maintenance or transporting the machine.

Be sure to release the frame locking bar during routine

travel.

The frame locking bar is used to lock the front and rear frames during maintenance or

transporting vehicles, in order to prevent the frames from moving.

1.2.7 Towing Pin

During towing, insert the towing pin into the

①

counterweight .

②

1.2.8 Fuse

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands