Volvo SDLG LG936L Operation & Maintenance Manual Download Page 51

Page: 51 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

negative or ground (

) cable first when the voltage-raising cable is removed.

Connect the ground cable to the frame of the broken machine. Connection should be as far as

possible away from the storage battery.

Do not let the voltage-raising cables touch each other or let the clamp touch the machine when

the voltage-raising cable is removed.

8.19 Maintenance and Storage of Tires

8.19.1 Maintenance of Tires

The Explosion of a tire can push the parts, such as tire, rim and driving axle, as far as 500m or

more. The explosion and the particles can lead to severe injury, even death, so please keep the

pressure of the tire at the normal level. Inflation pressure should not surpass the standing value.

The inflation pressure is shown in

CHAPTER II - 8 TECHNICAL PERFORMANCE

& PARAMETERS

Driving at high speeds increases the temperature, and therefore, the pressure.

Never

try to reduce

the pressure, but reduce the speed to cool the tire. Continuous high speed driving can lead to over

heating and tire explosion.

Stand at the back of the tire, and stand as far as possible away from the tire when adjusting the

pressure of the tire.

Check the tire and rim every day for cracks or bubbles.

Never

operate in a low pressure

condition.

Check that the bolt and nut of the rim are in place. Check whether the torque of the nut satisfies

the suggested value of the factory.

Never

stand in the front or the rear of the rolling direction of the tire. Check the tire from the side.

If disassembling one tire lock the other tires.

Take care when welding near a tire, which can cause explosion of the tire.

Only a trained person with a professional license can repair a tire and rim using specific tools and

following the proper steps.

Use the uniform tire with the same standard and same flower pattern for replacement.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands