Volvo SDLG LG936L Operation & Maintenance Manual Download Page 72

Page: 72 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

continuously turned; the machine rotation angle will increase until at the needed position.

The faster the steering wheel turns, the faster the machine turns.

The steering wheel will not automatically come back after turning, the turning angle of the

machine will be kept. After finishing turning the machine, turn the steering wheel in the reverse

direction to keep the machine moving in a straight direction.

1.2.4 Control Levers and Pedals

Shifting Control

Lever

This lever controls the
direction and traveling
speed of the machine.
When the lever is at N (0)
position, it means neutral
gear. Put the control lever forward to the 1 position can obtain the forward gear

Ⅰ

, and the machine

goes forward at low speed. When turn it to 2 position, the forward gear

Ⅱ

can be obtained, and the

machine goes forward at high speed. Putting the lever to R position can obtain the reverse gear and
the machine goes backward.

Equipment Control Handle and Lever

(1)

Equipment Control Lever

Refer to

1.1 General View of Controls and Gauges Figure 3-1, Figure 3-2

in this

chapter.

Bucket Control Lever

This lever controls the bucket which has

three positions.

Rear Tilt is used for drawing in

the bucket

Neutral is used for keeping the

bucket in the desired position.

Forward Tilt is used for dumping.

Lift Arm Control Lever

This lever controls the lift arm, which has

four positions.

Lift is used for lifting.

Neutral is used for maintaining the Position of Bucket

Control Lever

Position of Lift Arm
Control Lever

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands