Volvo SDLG LG936L Operation & Maintenance Manual Download Page 67

Page: 67 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

Pre-heat Indicator Lamp:

If assemble the pre-heat function, the lamp would be on if in the

pre-heating state or the light will be off.

Oil Pressure Warning Lamp:

The lamp will come on immediately if the start switch is turned

on. It will go off immediately after the engine is started. Otherwise it means the level of lubricant

is too low or there is some problem with the lubricant system. Then shut the engine and check it.

Charging Indicator Lamp:

The lamp will come on if the start switch is turned on. It will go off

immediately after the engine is started. Otherwise it means there is some problem with storage

battery. Please examine and repair it.

Power Cut Indicator Lamp:

The lamp will come on if the power is cut off, and it will go off if

the power is not cut off.

The power will be cut off and the lamp will come on if the left braking pedal is stepped down; the

power will not be cut off and the lamp will go off if the right braking pedal is stepped down.

Emergency Steering Indicator Lamp:

The emergency steering function is selected to install.

When the wheel loader is steered emergently, the lamp will come on if the emergency steering

pump works.

Parking Brake Indicator Lamp:

The lamp will come on when the parking brake switch is

pushed down and the brake air pressure is low. The lamp will go off when the brake air pressure

is normal and the parking brake switch springs back.

Low Brake Air Pressure Alarm Lamp:

The lamp will come on for a warning if the brake air

pressure is below 0.4MPa.

High Beam Indicator Lamp:

The lamp will come on if the high beam is used in the front

headlight. The lamp will be off if the dipped headlight is used or the front headlight is off.

Computer working Indicator Lamp:

If ZF gear box or 4WG180 gear box is assembled, the

lamp will come on when the starting switch is on, otherwise examine and repair it.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands