Volvo SDLG LG936L Operation & Maintenance Manual Download Page 30

Page: 30 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

the correct positions. Make sure all the control levers (or control handles) are easy to use.

Examine the foot brake valve and oil operation valve according to the user manual to make sure
that they are normal. Check whether the left turning and right turning is smooth at low speed.

Be sure the control lever of the manual brake valve is at rescission of braking state before moving
forward.

5 SAFETY DRIVING

5.1 Warning

The warning light should be turned on to warn the

other drivers on the road when the machine is

broken down or operating at a low speed.

5.2 Safety of self and Others

Develop good driving habits to ensure everyone’s

safety.

Sound the horn to ensure safety before moving.

Be sure there are no people or blockage on the left

and right side.

Check the brakes on dry and firm, level ground.

Do not put an arm or foot on the working equipment or extend outside the machine.

When driving on the level ground, adjust the lower

hinge of the arm working equipment to 400

～

500mm(16

～

20in) above the ground.

Summary of Contents for SDLG LG936L



































































































































Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands

Volvo SDLG LG936L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG936L

Reviews:

Related manuals for SDLG LG936L

Brands by name

Popular brands