Tundra TSI308 User Manual Download Page 98 | Manualshive

Page: 98 / 260

background image

4. Register Descriptions

98

Tsi308 User Manual

80D4000_MA001_02

Tundra Semiconductor Corporation

www.tundra.com

4.3.5.3

Command Register

Register Offset : 05h–04h

Bit

R/W

Access

Initial
Value

Field Name and Description

15:11

R

0

Reserved:

always reads 0.

10

R

0

SP/DSP:

Reserved (always reads 0).

GSP/ GDP:

Interrupt Disable:

If clear allows Tsi308 to assert a legacy INTx pin(if implemented) or send an INTx
assertion message.

Not persistent through warm reset.

Tsi308 doesn’t support it. Treated as reserved and reads 0.

9

R

0

FastB2Ben:

This has no meaning for HyperTransport. Always reads 0.

8

R/W

0

SerrEn:

SP/DSP: This enables system error interrupt pins FATAL_ERR_N and
NONFATAL_ERR_N to be driven.

0 = SERR_N output driver disabled (default).

1 = SERR_N output driver enabled.

GSP/ GDP:

If this bit is set, Tsi308 floods all its outgoing links with sync packets when it detects
an error that causes a sync flood. It this bit is clear, Tsi308 does not generate sync
packets except as part of initial link synchronization, although it can still propagate
them from one link to other within a chain.

Not persistent through warm reset.

7

R

0

WaitCycCtrl:

This has no meaning for HyperTransport. Always reads 0.

«
...
96
97
98
99
100
...
»

Summary of Contents for TSI308





































































































































































































































































Reviews:

No comments

Related manuals for TSI308

Brand: CAME Pages: 4

Brand: IBM Pages: 248

Brand: Aastra Pages: 2

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

Brand: Harmonic Pages: 56

Brand: TP-Link Pages: 73

DHI-NVR2104-P-4KS2

Brand: Dahua Pages: 23

Brand: TP-Link Pages: 2

Brand: NA Pages: 22

Brand: Zoom Pages: 88

Brand: Radicom Pages: 27

Brand: axing Pages: 4

PSoC 4 S Series

Brand: Cypress Pages: 4

Brand: ADS Technologies Pages: 21

Brand: Xilinx Pages: 43

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

JetNet 5720G-8P Series

Brand: Korenix Pages: 52

Brand: Billion Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands