manualshive.com logo in svg

Tundra TSI308, User Manual

Looking to download a free User Manual for the Tundra TSI308? Look no further! Find all the answers you need on manualshive.com, where you can easily download the comprehensive manual for the Tundra TSI308. Accessible, detailed instructions are just a click away!

Share
Download
background image

4. Register Descriptions

147

Tsi308 User Manual

80D4000_MA001_02

Tundra Semiconductor Corporation

www.tundra.com

4.3.5.51

Read Control 2 Register

These registers are reserved in SP/DSP modes. But they are valid in GSP and GDP modes.  The 
attributes of Read Control 2 registers are applied for upstream packets instead of Read Control 
1(62h-60h) if the an address of upstream request falls in DMA window of Address Remapping 
Indices. 

Register Offset : 5Eh–5Ch

Bit

R/W 

Access

Initial 
Value

Field Name and Description

23:22

R

000b

Reserved.

21:19

R/W

000b

Line Prefetch Initial Count:

Indicates the minimum number of lines that must be successfully prefetched from 
memory on a MemRdLine (or MemRd if prefetching is enabled for MemRd 
commands) before allowing the PCI requester to reconnect. Not persistent through 
warm reset.

18:16

R/W

000b

Multiple Prefetch Initial Count:

Indicates the minimum number of lines that must be successfully prefetched from 
memory on a MemRdMult before allowing the PCI requester to reconnect. Not 
persistent through warm reset.

15:12

R/W

0h

Reserved.

11

R/W

0

Line Prefetch Continue:

If set, and prefetching for MemRdLine commands is enabled, MemRdLine (and 
MemRd, if prefetching is enabled for MemRd commands) prefetching will be 
continuous. As each line of data is returned to PCI, another line will be read from 
HyperTransport, creating a moving prefetch window. Otherwise, prefetching will 
end when the specified number of lines has been fetched. Not persistent through 
warm reset.

10

R/W

0

MultPrefetchContinue:

If set, and prefetching for MemRdMult commands is enabled, MemRdMult 
prefetching will be continuous. As each line of data is returned to PCI, another line 
is read from HyperTransport, creating a moving prefetch window. Otherwise, 
prefetching will end when the specified number of lines has been fetched. Not 
persistent through warm reset.

9:8

R/W

00b

PCI Delayed Requests:

This controls the number of PCI delayed requests that may be outstanding at one 
time. The value in the register plus 1 is the number that will be allowed, enabling 
from one to four buffers. Not persistent through warm reset.

Summary of Contents for TSI308





































































































































































































































































Reviews:

No comments

Related manuals for TSI308

GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
CallDirect CD Series At Command Manual preview
CD Series
Brand: CallDirect Pages: 33
3Com 3C3FE574BT Quick Start Manual preview
3C3FE574BT
Brand: 3Com Pages: 8
Tyco Electronics 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink Product User Manual preview
8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink
Brand: Tyco Electronics Pages: 18
Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Cabletron Systems MMAC-Plus 9F106-02 Reference Manual preview
MMAC-Plus 9F106-02
Brand: Cabletron Systems Pages: 7
Vanguard 342 Quick Reference Manual preview
342
Brand: Vanguard Pages: 4
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
TwinMOS Octopus G Series User Manual preview
Octopus G Series
Brand: TwinMOS Pages: 29
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
B&B Electronics EIR208 Series Quick Start Manual preview
EIR208 Series
Brand: B&B Electronics Pages: 2
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
Microchip Technology DM240316 Quick Start Manual preview
DM240316
Brand: Microchip Technology Pages: 9
ekwb 3831109826140 User Manual preview
3831109826140
Brand: ekwb Pages: 11

Brands by name

Popular brands

Load more brands