Tundra TSI308 User Manual Download Page 102 | Manualshive

Page: 102 / 260

background image

4. Register Descriptions

102

Tsi308 User Manual

80D4000_MA001_02

Tundra Semiconductor Corporation

www.tundra.com

11

R/C

0

Signaled Target Abort:

This bit reports the signaling of a target abort termination by the bridge, when it
responds as the target of a transaction on its primary interface. This is indicated on
HyperTransport by a response with the error bit set. It may be cleared by writing a 1 to
it.

Persistent through warm reset.

10:9

R

00b

DEVSEL_N Timing:

Encodes the timing of the primary interface's DEVSEL. This is not meaningful for
HyperTransport. Always reads 00.

DEVSEL_N Timing always reads 00.

8

R(SP/DSP

)

R/C(GSP/

GDP)

0

SP/DSP:

PCI Parity Error Detected:

This bit is used to report the detection of a parity error by the bridge when it is the
master of the transaction. HyperTransport doesn't have parity errors.

GSP/ GDP:

Master Data Error:

This bit is set by Tsi308 if Data Error Response bit of Command register is set and if
Tsi308 issues a posted request on primary interface with Data Error bit set or accepts
a response from primary interface with a Data Error indicated.

This bit is not set if only forwarding packets with the Data Error bit set.

Persistent through warm reset.

7

R

0

Fast BacktoBack Capability:

This is not meaningful for HyperTransport. Always reads 0.

6

R

0

Reserved:

(always reads 0).

5

R

0

66 MHz Capable PCI Bus:

Indicates whether the primary interface is 66 MHz capable. Not meaningful for
HyperTransport. Always reads 0.

Bit

R/W

Access

Initial
Value

Field Name and Description

«
...
100
101
102
103
104
...
»

Summary of Contents for TSI308





































































































































































































































































Reviews:

No comments

Related manuals for TSI308

SAFETank Series

Brand: Raidon Pages: 49

Brand: Ubiquiti Pages: 22

Brand: Ublox Pages: 17

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: FS Pages: 19

Brand: ProCurve Pages: 2

RanaSystems 13-0010--001

Brand: RANA Systems Pages: 328

Brand: SYNTEK Pages: 41

Sinus 154 data II

Brand: T-COM Pages: 12

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: MA lighting Pages: 49

802.11a/b/g SDIO WiFi Module SDM3100

Brand: Abocom Pages: 14

Brand: Mobily Pages: 12

FiberTwist XGS2420

Brand: Genexis Pages: 7

Brand: Kordis Pages: 31

BPN-SAS3-116A-N10

Brand: Supermicro Pages: 8

Brand: Paradyne Pages: 28

Brand: ZyXEL Communications Pages: 263

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands