Tundra TSI308 User Manual Download Page 78 | Manualshive

Page: 78 / 260

background image

3. Clock Frequency and Mode Selection Hardware Straps

78

Tsi308 User Manual

80D4000_MA001_02

Tundra Semiconductor Corporation

www.tundra.com

3.8

Miscellaneous Straps

lists the other miscellaneous mode selection straps.

Table 19: Miscellaneous Pin Straps

Strap / Pin Number

Description

Encoding

Comments

P0_AD[19] / A10

Link 0 Sync Pointer Control:

When set, indicates that Link 0 transmit
clock is derived from the same time base as
the receive clock in the device to which it is
connected.

That means P0_CLK that is used by Tsi308
to generate L0_TX_CLK_H/L should be
used by the device that is connected to
Tsi308’s Link 0 to generate its internal core
clock that receives the data from Link 0.

0 -> Async

1 -> Sync

P0_AD[18] / B10

Link 1 Sync Pointer Control:

When set, indicates that Link 1 transmit
clock is derived from the same time base as
the receive clock in the device to which it is
connected.

That means P0_CLK that is used by Tsi308
to generate L1_TX_CLK_H/L should be
used by the device that is connected to
Tsi308’s Link 1 to generate its internal core
clock that receives the data from Link 1.

0 -> Async

1 -> Sync

P0_AD[14] / B9

PCI/PCI-X Bus 0 Data Width:

Configures the Tsi308 either as a single
64-bit bus or dual 32-bit (split bus) mode.

0 -> 64-bit

1 -> 32-bit

P0_AD[2] / B5

PCI/PCI-X Bus 1 Enable:

When set, enables Tsi308’s 2

nd

32-bit

PCI/PCI-X bus.

When cleared, Tsi308 will operate in single
32-bit or 64-bit bus mode depending on the
value set on P0_AD[14].

1 -> Enabled

0 -> Disabled

May be set only

when

P0_AD[14] is

cleared.

«
...
76
77
78
79
80
...
»

Summary of Contents for TSI308





































































































































































































































































Reviews:

No comments

Related manuals for TSI308

Brand: Keithley Pages: 59

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: Paradyne Pages: 45

Brand: FOR-A Pages: 39

Brand: Barco Pages: 121

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Brand: Gate Pages: 8

Brand: Taiwan Commate Computer Inc. Pages: 29

MasterBus Tanklevel Interface

Brand: Mastervolt Pages: 8

Marconi OMS 1200

Brand: Ericsson Pages: 136

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

kontron KBox E-420-R1K/V1K

Brand: S&T Pages: 82

Brand: NetComm Pages: 69

Brand: Gbord Pages: 8

Brand: Datasat Pages: 24

Brand: Glacier Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands