Toyota AVALON 2005 Operating Manual Download Page 80 | Manualshive

Page: 80 / 319

background image

’05 MATRIX_U (L/O 0409)

80

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

(C) BOOSTER SEAT INSTALLATION

A booster seat must be used in for-
ward- facing position only.

Move seat
fully back

CAUTION

A forward- facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible even if the front pas-
senger occupant classification indi-
cator light indicates “OFF”, because
the front passenger airbag could in-
flate with considerable speed and
force. Otherwise, the child may be
killed or seriously injured.

Do not allow the child to lean his/
her head or any part of his/her
body against the door or the area
of the seat, front or rear pillar or
roof side rail from which the side
airbags or curtain shield airbags
deploy even if the child is seated in
the child restraint system. It is dan-
gerous if the side airbag and cur-
tain shield airbag inflate, and the
impact could cause death or seri-
ous injury to the child.

«
...
78
79
80
81
82
...
»

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Brand: Front Runner Pages: 5

Brand: Rola Pages: 3

Brand: WABCO Pages: 32

Brand: iArmor Pages: 4

Brand: Alfa Romeo Pages: 8

Brand: Yakima Pages: 9

Brand: Cadillac Pages: 352

Brand: iDataLink Pages: 6

Brand: WABCO Pages: 34

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: Grillo Pages: 71

Brand: CSL Pages: 8

Brand: Kuda Pages: 3

Brand: Ranger design Pages: 22

Brand: ideus Pages: 116

Brand: Scosche Pages: 32

Brand: TrailFX Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands