Toyota AVALON 2005 Operating Manual Download Page 39 | Manualshive

Page: 39 / 319

background image

’05 MATRIX_U (L/O 0409)

39

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

CAUTION

Avoid reclining the seatback any
more than needed. The seat belts pro-
vide maximum protection in a frontal
or rear collision when the driver and
the front passenger are sitting up
straight and well back in the seats. If
you are reclined, the lap belt may
slide past your hips and apply re-
straint forces directly to the abdomen
or your neck may contact the shoul-
der belt. In the event of a frontal
collision, the more the seat is re-
clined, the greater the risk of death
or personal injury.

1. Lower the head restraint to the low-

est position and fix the seatback at
the most upright lock position.

2. Pull up either seatback lock release

knob beside the seatback and fold
the seatback down.

CAUTION

Do not sit on or place anything on
the folded seatback to avoid serious
injury while the vehicle is moving.

—Fold- down front
passenger’s seat

«
...
37
38
39
40
41
...
»

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Brand: Hama Pages: 2

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Brand: Dometic GROUP Pages: 20

Brand: Toyota Pages: 35

Brand: Subaru Pages: 21

Brand: Whispbar Pages: 85

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Brand: Xhorse Pages: 48

Brand: Warn Pages: 5

Brand: cam Pages: 28

Brand: ULTIMATE SPEED Pages: 40

Brand: POOL-LINE Pages: 2

Brand: Ford Pages: 15

Brand: Honda Pages: 3

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brand: Butts of Bawtry Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands