manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

122

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

(g) Parking

1. Bring the vehicle to a complete stop.

2. With the brake pedal pressed down,

fully depress the parking brake pedal
to apply the parking brake securely.

3. With the brake pedal pressed down,

shift the selector lever to the “P” posi-
tion.

CAUTION

Never attempt to move the selector
lever into “P” position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.

(h) Good driving practice

If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope, the
overdrive should be turned off. Be sure
to turn the switch on immediately after-
ward.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.

CAUTION

Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.

NOTICE

Always use the brake pedal or the
parking brake to hold the vehicle on
an upgrade. Do not attempt to hold
the vehicle using the accelerator ped-
al, as this can cause the transmission
to overheat.

(i)

If you cannot shift the selector le-
ver out of “P” position

If you cannot shift the selector lever from
the “P” position even though the brake
pedal is depressed, use the shift lock
override button. For instructions, see “If
you cannot shift automatic transmission
selector lever” on page 247 in Section 4.

5- speed

6- speed

Manual transmission

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Brand: Jeep Pages: 673
Roav R5141 Owner'S Manual preview
R5141
Brand: Roav Pages: 10
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Brand: Romik Pages: 6
Honda 2011 Civic Sedan Vehicle Instruction Card preview
2011 Civic Sedan
Brand: Honda Pages: 5
Suzuki 990E0-54P56-000 Installers And Users Instructions preview
990E0-54P56-000
Brand: Suzuki Pages: 12
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Brand: Xpresskit Pages: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Brand: RAM Pages: 92
Whipple TOMAHAWK V1 Instruction Manual preview
TOMAHAWK V1
Brand: Whipple Pages: 3
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Brand: Fast Master Products Pages: 13
Kia Bluetooth Phone System 2010 Reference Manual preview
Bluetooth Phone System 2010
Brand: Kia Pages: 16
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Brand: KLAUS Multiparking Pages: 72
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Brand: Sintrones Pages: 55
MMD 41240 Quick Manual preview
41240
Brand: MMD Pages: 3
travall TDG1166 Fitting Instructions preview
TDG1166
Brand: travall Pages: 4
LAS 10329 Operating Instructions Manual preview
10329
Brand: LAS Pages: 10
Peiying PY-EM01 Owner'S Manual preview
PY-EM01
Brand: Peiying Pages: 28
Lippert Components X-Trek Installation Manual preview
X-Trek
Brand: Lippert Components Pages: 14
Monzana 105573 Instructions preview
105573
Brand: Monzana Pages: 5

Brands by name

Popular brands

Load more brands