Toyota AVALON 2005 Operating Manual Download Page 31 | Manualshive

Page: 31 / 319

background image

’05 MATRIX_U (L/O 0409)

31

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

3. Hold the hood open by inserting the

support rod into the slot.

To insert the support rod into the slot,
move it straight up. If it is moved to the
side or toward the inside of the vehicle,
it may become detached.

Before closing the hood, check to see that
you have not forgotten any tools, rags,
etc. and return the support rod to its
clip—this prevents rattles. Then lower the
hood and make sure it locks into place.
If necessary, press down gently on the
front edge to lock it.

CAUTION

After inserting the support rod into
the slot, make sure the rod supports
the hood securely from falling down
on to your head or body.

NOTICE

Be sure to return the support rod to
its clip before closing the hood. Clos-
ing the hood with the support rod up
could cause the hood to bend.

This indicates that the fuel filler door
is on the left side of your vehicle.

Fuel tank cap

«
...
29
30
31
32
33
...
»

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Brand: B-Speech Pages: 18

Brand: VanEssa mobilcamping Pages: 8

Brand: Ford Pages: 2

Brand: Honda Pages: 208

Brand: STC Pages: 6

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Brand: CALIMA Pages: 9

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: Velleman Pages: 12

Brand: iArmor Pages: 6

Brand: Honda Pages: 268

Brand: Roadmaster Pages: 4

Brand: PEUGEOT Pages: 232

Brand: Arrista Pages: 2

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Istar Pages: 6

Brand: JBA Pages: 5

Brand: Volkswagen Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands