Toyota AVALON 2005 Operating Manual Download Page 269

Page: 269 / 319

’05 MATRIX_U (L/O 0409)

269

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

CHECKING AND REPLACING FUSES

Parts (if replacement is necessary):

Fuse with same amperage rating as
original

ADDING WASHER FLUID

Parts:

Water

Washer fluid containing antifreeze
(for winter use)

Tools:

Funnel

REPLACING LIGHT BULBS

Parts:

Bulb with same number and wattage
rating as original (See charts in
“Replacing light bulbs” on page 292 in
Section 7- 3.)

Tools:

Screwdriver

Front

Rear (two- wheel drive models)

Rear (four- wheel drive models)

When jacking up your vehicle with the
jack, position the jack correctly as
shown in the illustrations.

CAUTION

When jacking, be sure to observe the
following to reduce the possibility of
personal injury:

Follow jacking instructions.

Do not put any part of your body
under the vehicle supported by the
jack. Personal injury may occur.

Positioning the jack

Summary of Contents for AVALON 2005
































































































































































































































































































































Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands

Toyota AVALON 2005, Operating Manual

Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands