manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

279

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Tire pressure gauge

INSPECTION AND ADJUSTMENT
PROCEDURE

1. Remove the tire valve cap.

2. Press the tip of the tire pressure

gauge to the tire valve.

3. Read the pressure using the grad-

uations of the gauge.

4. In case the tire inflation pressure

is not within the prescribed range,
insert the compressed air from the
valve. In case of applying too
much air, press the center of the
valve and release the air to adjust.

5. After completing the tire inflation

pressure measurement and ad-
justment, apply soapy water to the
valve and check for leakage.

6. Install the tire valve cap.

If a gauge and air pump are not avail-
able, have your vehicle checked by
your Toyota dealer.

CAUTION

Be sure to reinstall the tire valve
caps. Without the valve caps, dirt
or moisture could get into the
valve core and cause air leakage.
If the caps have been lost, have
new ones put on as soon as pos-
sible.

Incorrect tire inflation pressure may
waste fuel, reduce the comfort of driv-
ing, reduce tire life and make your ve-
hicle less safe to drive.

If a tire frequently needs refilling,
have it checked by your Toyota deal-
er.

CAUTION

Keep your tires properly inflated.
Otherwise, the following condi-
tions may occur and cause an ac-
cident resulting in death or seri-
ous injuries.

Low tire pressure (underinfla-
tion)—

Excessive wear

Uneven wear

Poor handling

Possibility of blowouts from an
overheated tire

Poor sealing of the tire bead

Wheel deformation and/or tire
separation

A greater possibility of tire
damage from road hazards

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

A-Tach Mounts ST-1 Instructions preview
ST-1
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50206 Instructions preview
50206
Brand: A-Tach Mounts Pages: 2
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Brand: Fabbri Pages: 4
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Brand: Camcar Pages: 2
DAVIS 8126GD User Manual preview
8126GD
Brand: DAVIS Pages: 32
Alpine eX-10 Owner'S Manual preview
eX-10
Brand: Alpine Pages: 69
Allen Sports S302 Instructions preview
S302
Brand: Allen Sports Pages: 2
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Brand: Streetwize Pages: 20
Thule 1511 Instructions Manual preview
1511
Brand: Thule Pages: 8
WABCO TP19108 Installation Manual preview
TP19108
Brand: WABCO Pages: 32
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Brand: Waeco Pages: 172
Ecco Vantage 12 Series Installation And Operation Instructions preview
Vantage 12 Series
Brand: Ecco Pages: 5
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Brand: WABCO Pages: 52
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3

Brands by name

Popular brands

Load more brands