Toyota AVALON 2005 Operating Manual Download Page 293

Page: 293 / 319

’05 MATRIX_U (L/O 0409)

293

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Light bulbs

Bulb

No.

Type

Interior lights

—

Personal lights
(on the inside
rear view mirror
without compass)

192

4.3

Personal lights
(on the switch
panel of the
electric moon
roof)

—

A: HB4 halogen bulbs
B: HB3 halogen bulbs
C: Single end bulbs
D: Wedge base bulbs (clear)
E: Wedge base bulbs (amber)

1. Open the hood. Turn the bulb base

counterclockwise to the front of the
vehicle as shown.

2. Unplug the connector.

If the connector is tight, wiggle it.

—Headlights (low beam)

Summary of Contents for AVALON 2005
































































































































































































































































































































Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands

Toyota AVALON 2005, Operating Manual

Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands