Toyota AVALON 2005 Operating Manual Download Page 307

Page: 307 / 319

’05 MATRIX_U (L/O 0409)

307

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Engine compartment

Instrument panel

Fuses (type A)

1. FOG 15 A: Front fog lights

2. HEAD LH UPR 10 A: Left- hand head-

light (high beam)

3. HEAD RH UPR 10 A: Right- hand

headlight (high beam), headlight high
beam indicator light

4. SPARE 30 A: Spare fuse

5. SPARE 15 A: Spare fuse

6. SPARE 10 A: Spare fuse

7. ETCS 10 A (1ZZ- FE engine with two-

wheel drive models only): Electronic
throttle control system

8. AMP 30 A: Car audio system

9. MAIN 30 A: Starting system, “AM2”

fuse

10. DOME 15 A: Car audio system, navi-

gation system, clock, personal lights,
interior lights, open door warning light,
wireless remote control system

11. HORN 10 A: Horn

12. HAZARD 10 A: Emergency flashers,

turn signal lights

13. EFI 15 A: Multiport fuel injection sys-

tem/sequential multiport fuel injection
system, emission control system, “EFI”
fuse

14. ALT- S 5 A: Charging system

15. HEAD LH LWR 10 A: Left- hand head-

light (low beam)

16. HEAD RH LWR 10 A: Right- hand

headlight (low beam)

17. EFI2 15 A: (1ZZ- FE engine with two-

wheel drive models only): Multiport
fuel injection system/sequential multi-
port fuel injection system, emission
control system

18. TAIL 15 A: Tail lights, license plate

lights, instrument panel lights, instru-
ment cluster lights, clock

Fuses

Summary of Contents for AVALON 2005
































































































































































































































































































































Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands

Toyota AVALON 2005, Operating Manual

Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands