manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

60

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

8. Front passenger’s seat belt buckle

switch

9. Airbag sensor assembly

The SRS side airbag and curtain shield
airbag system is controlled by the airbag
sensor assembly. The airbag sensor as-
sembly consists of a safing sensor and
airbag sensor.

In a severe side impact, the side and
curtain shield airbag sensor and/or the
curtain shield airbag sensor trigger(s) the
side airbag inflators and/or the curtain
shield airbag inflators. At this time a
chemical reaction in the inflators quickly
fills the airbags with non- toxic gas to help
restrain the lateral motion of the occu-
pants.

When the airbags inflate, they produce a
fairly loud noise and release some smoke
and residue along with non- toxic gas. This
does not indicate a fire. This smoke may
remain inside the vehicle for some time,
and may cause some minor irritation to
the eyes, skin or breathing. Be sure to
wash off any residue as soon as possible
to prevent any potential skin irritation with
soap and water. If you can safely exit
from the vehicle, you should do so imme-
diately.

Deployment of the airbags happens in a
fraction of a second, so the airbags must
inflate with considerable force. While the
system is designed to reduce serious inju-
ries, it may also cause minor burns or
abrasions and swelling.

Front seats as well as parts of the front
and rear pillars, and roof side rail may be
hot for several minutes, but the airbags
themselves will not be hot. The airbags
are designed to inflate only once.

CAUTION

SRS side airbags and curtain shield
airbags inflate with considerable
force. To reduce the possibility of
death or serious injury when they in-
flate, the driver, front passenger and
rear outside passengers must:

Wear their seat belts properly.

Remain properly seated with their
backs upright and against the seats
at all times.

Do not allow anyone to lean against
the door when the vehicle is in use,
since the side airbag and curtain
shield airbag could inflate with con-
siderable speed and force. Other-
wise, he/she may be killed or seri-
ously injured. Special care should
be taken especially when you have
a small child in the vehicle.

Sit up straight and well back in the
seat, distributing your weight evenly
in the seat. Do not apply excessive
weight to the outer side of the
seats with a side airbag, and to the
front pillar, rear pillar and roof side
rail with a curtain shield airbag.

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Brand: Cadillac Pages: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Brand: Cadillac Pages: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Brand: Cadillac Pages: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Brand: Cadillac Pages: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Brand: Cadillac Pages: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Brand: Cadillac Pages: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Brand: Cadillac Pages: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Brand: Cadillac Pages: 438
KAP AUDI 4G HIGHEND Manual preview
AUDI 4G HIGHEND
Brand: KAP Pages: 20
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Brand: Yamaha Pages: 3
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Brand: GOgroove Pages: 9
Daewoo RACER 1998 Electrical Wiring Diagram preview
RACER 1998
Brand: Daewoo Pages: 68
Hyundai Getz 2004 Owner'S Manual preview
Getz 2004
Brand: Hyundai Pages: 437

Brands by name

Popular brands

Load more brands