Toyota AVALON 2005 Operating Manual Download Page 72 | Manualshive

Page: 72 / 319

background image

’05 MATRIX_U (L/O 0409)

72

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

(A) INFANT SEAT INSTALLATION

An infant seat must be used in rear-
facing position only.

CAUTION

Never install a rear- facing child re-
straint system on the front passen-
ger seat even if the front passenger
occupant classification indicator
light indicates “OFF”. In the event
of an accident, the impact of the
rapid inflation of the front passen-
ger airbag could cause death or se-
rious injury to the child if the rear-
facing child restraint system is
installed on the front passenger
seat.

Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant(s) may be killed
or seriously injured in case of sud-
den braking or a collision.

If the driver’s seat position does
not allow sufficient space for safe
installation, install the child re-
straint system on the rear right
seat. Child restraint system
installed on the rear seat should
not contact the front seatbacks.

—Installation with seat belt

«
...
70
71
72
73
74
...
»

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: Garmin Pages: 2

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Wallbox eM4 Single

Brand: ABL Pages: 68

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Indigo MANZA QUADRAJET 90

Brand: TATA Motors Pages: 10

Brand: Ford Pages: 38

Brand: AutoWatch Pages: 4

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: PAC Pages: 4

Brand: Alfa Romeo Pages: 8

Brand: Thule Pages: 2

Brand: Jaeger Pages: 17

1995 Cutlass Supreme

Brand: Oldsmobile Pages: 340

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands