manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

44

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

When a passenger’s shoulder belt is com-
pletely extended and is then retracted
even slightly, the belt is locked in that
position and cannot be extended. This fea-
ture is used to hold the child restraint
system securely. (For details, see “Child
restraint” on page 69 in this Section.) To
free the belt again, fully retract the belt
and then pull the belt out once more.

If the seat belt cannot be pulled out of the
retractor, firmly pull the belt and release
it. You will then be able to smoothly pull
the belt out of the retractor.

CAUTION

After inserting the tab, make sure
the tab and buckle are locked and
that the belt is not twisted.

Do not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and
buckle.

If the seat belt does not function
normally, immediately contact your
Toyota dealer. Do not use the seat
until the seat belt is fixed, because
it cannot protect an adult occupant
or your child from injury.

Take up
slack

Too high

Keeps as low on
hips as possible

Adjust the position of the lap and
shoulder belts.

Position the lap belt as low as possible
on your hips—not on your waist, then ad-
just it to a snug fit by pulling the shoulder
portion upward through the latch plate.

CAUTION

Both high- positioned lap belts and
loose- fitting belts could cause seri-
ous injuries due to sliding under
the lap belt during a collision or
other unintended event. Keep the
lap belt positioned as low on hips
as possible.

Do not place the shoulder belt un-
der your arm.

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

iDataLink Maestro Installation Manual preview
Maestro
Brand: iDataLink Pages: 9
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Brand: Axxess Pages: 4
Vintage Air 473275 Manual preview
473275
Brand: Vintage Air Pages: 14
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Brand: Mazda Pages: 400
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Brand: RAM Pages: 174
Volvo 2006 XC70 Owner'S Manual preview
2006 XC70
Brand: Volvo Pages: 211
Mitsubishi MOTORS PAJERO SPORT Manual preview
PAJERO SPORT
Brand: Mitsubishi MOTORS Pages: 416
Classic AutoAir Mustang 1969 Installation Manual preview
Mustang 1969
Brand: Classic AutoAir Pages: 44
TracRac TracVan Double Installation Instructions Manual preview
TracVan Double
Brand: TracRac Pages: 6
CAME UNIPARK ARK1 Manual preview
UNIPARK ARK1
Brand: CAME Pages: 14
Yakima RIpCord Manual preview
RIpCord
Brand: Yakima Pages: 12
BrandMotion AVMS-3604 Installation Instructions Manual preview
AVMS-3604
Brand: BrandMotion Pages: 9
Discount Car Stereo A2DIY-CHRY Installation Manual preview
A2DIY-CHRY
Brand: Discount Car Stereo Pages: 5
Sharp IG-DC2B Operation Manual preview
IG-DC2B
Brand: Sharp Pages: 74
Bosch Mastertech Vehicle Communication Interface User Manual preview
Mastertech Vehicle Communication Interface
Brand: Bosch Pages: 17
RAM RAM CV Cargo Van 2012 Owner'S Manual preview
RAM CV Cargo Van 2012
Brand: RAM Pages: 642
Axxess AXDIS-CL2 Installation Instructions Manual preview
AXDIS-CL2
Brand: Axxess Pages: 12
Toyota 100 Series Manual preview
100 Series
Brand: Toyota Pages: 11

Brands by name

Popular brands

Load more brands