Toyota AVALON 2005 Operating Manual Download Page 305

Page: 305 / 319

’05 MATRIX_U (L/O 0409)

305

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

TRANSFER
(four- wheel drive models)

Oil capacity, L (qt., Imp. qt.):

0.8 (0.8, 0.7)

Oil type:

Hypoid gear oil API GL- 5

Recommended oil viscosity:

Above -18

C (0

SAE 90

Below -18

C (0

SAE 85W or 85W- 90

REAR DIFFERENTIAL
(four- wheel drive models)

Oil capacity, L (qt., Imp. qt.):

0.5 (0.5, 0.4)

Oil type:

Hypoid gear oil API GL- 5

Recommended oil viscosity:

Above -18

C (0

SAE 90

Below -18

C (0

SAE 85W or 85W- 90

BRAKES

Minimum pedal clearance when depressed
with the force of 294 N (30 kgf, 66 lbf)
with the engine running, mm (in.):

Without anti- lock brake system

78 (3.07)

With anti- lock brake system

76 (2.99)

Pedal free play, mm (in.):

1—6 (0.04—0.24)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake adjustment when pulled with
the force of 196 N (20 kgf, 44 lbf):

5—8 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING

Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRON

or III

Summary of Contents for AVALON 2005
































































































































































































































































































































Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands

Toyota AVALON 2005, Operating Manual

Search results

Summary of Contents for AVALON 2005

Reviews:

Related manuals for AVALON 2005

Brands by name

Popular brands