manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

124

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Good driving practice

If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use fifth gear (5- speed models) or
sixth gear (6- speed models).

CAUTION

Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.

NOTICE

Make sure the vehicle is completely
stopped before shifting into reverse.

The traction control system automatical-
ly helps prevent the spinning of front
wheels when the vehicle is started or
accelerated on slippery road surfaces.

When the ignition key is turned to “ON”,
the system automatically turns on.

CAUTION

Under certain slippery road condi-
tions, full traction of the vehicle and
power against front wheels cannot be
maintained, even though the traction
control system is in operation. Do not
drive the vehicle under any speed or
maneuvering conditions which may
cause the vehicle to lose traction
control. In situations where the road
surface is covered with ice or snow,
your vehicle should be fitted with
snow tires or tire chains. Always
drive at an appropriate and cautious
speed for the present road condi-
tions.

NORMAL DRIVING MODE

Leave the system on during the ordi-
nary driving so that it can operate
when needed.

You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the trac-
tion control system is in the self- check
mode, but does not indicate a malfunction.

Traction control system

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Brand: Cadillac Pages: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Brand: Cadillac Pages: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Brand: Cadillac Pages: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Brand: Cadillac Pages: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Brand: Cadillac Pages: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Brand: Cadillac Pages: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Brand: Cadillac Pages: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Brand: Cadillac Pages: 438
EUFAB 12015 Manual preview
12015
Brand: EUFAB Pages: 12
PEUGEOT 407 2010 Manual preview
407 2010
Brand: PEUGEOT Pages: 249
Baja Designs 447575 Instructions preview
447575
Brand: Baja Designs Pages: 5
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Brand: PAC Pages: 14
Kolpin 98310 Product Instructions preview
98310
Brand: Kolpin Pages: 3
Kuda 079020 Installation Instruction preview
079020
Brand: Kuda Pages: 2
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112
Audi 2011 A3 Sportback Pricing And Specification Manual preview
2011 A3 Sportback
Brand: Audi Pages: 29
Quadratec QuadraTop 11051.0415 Installation Manual preview
QuadraTop 11051.0415
Brand: Quadratec Pages: 8

Brands by name

Popular brands

Load more brands