manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

169

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

The direction is indicated on the inside
rear view mirror.

If the ignition switch was turned off with
the system on, the system will automati-
cally turn back on when the ignition switch
is turned on.

To turn on the compass, push and hold
the “

” switch until the display turns

on.
To turn off the compass, push and hold
the “

” switch until the display turns

off.

The compass indicates the direction
that the vehicle is heading. In the
above case, it shows that the vehicle is
heading north.

Displays

Directions

N

NE

E

SE

S

SW

W

NW

North

Northeast

East

Southeast

South

Southwest

West

Northwest

The compass may not show the correct
direction in the following conditions:

The vehicle is stopped immediately af-
ter turning.

The compass does not adjust while the
vehicle is stopped.

The ignition switch is turned off imme-
diately after turning.

The vehicle is on an inclined surface.

The vehicle is in a place where the
earth’s magnetic field is subject to in-
terference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).

The vehicle is magnetized. (There is a
magnet or a metal object on or near
the inside rear view mirror.)

The battery has been disconnected.

If your vehicle is out of the set zone,
refer to “CALIBRATING THE COMPASS”
below to set the zone number.

If the deviation is small, the compass
works to calibrate the direction automati-
cally while the vehicle is in motion.

For additional precision or for complete
calibrating, see “CALIBRATING THE
COMPASS” below.

Compass

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Brand: Uniden Pages: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Brand: Uniden Pages: 20
Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Brand: Yakima Pages: 8
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Brand: GMC Pages: 20
Trailboss HD86 Fitting Instructions preview
HD86
Brand: Trailboss Pages: 5
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Brand: Kia Pages: 10
PEUGEOT 407 2010 Manual preview
407 2010
Brand: PEUGEOT Pages: 249
Harbor Freight Tools 66242 User Manual preview
66242
Brand: Harbor Freight Tools Pages: 12
Honda 0SR95-HL4-211A Installation Instructions preview
0SR95-HL4-211A
Brand: Honda Pages: 3
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Brand: Enduro Pages: 48
Cadillac 2009 CTS Personalization Manual preview
2009 CTS
Brand: Cadillac Pages: 20
BMW M5 2014 Service And Warranty Information preview
M5 2014
Brand: BMW Pages: 38
Volvo 164 1969 Service Manual preview
164 1969
Brand: Volvo Pages: 266
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Brand: Rostra Pages: 2
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
Oldsmobile 2003 Silhouette Owner'S Manual preview
2003 Silhouette
Brand: Oldsmobile Pages: 466
Curtis 1POLXP1000RP Installation & Owner'S Manual preview
1POLXP1000RP
Brand: Curtis Pages: 6
Cadillac ESCALADE ESV 2005 Owner'S Manual preview
ESCALADE ESV 2005
Brand: Cadillac Pages: 482

Brands by name

Popular brands

Load more brands