manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

227

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

To avoid serious personal injury and
damage to your vehicle which might re-
sult from battery explosion, acid burns,
electrical burns, or damaged electronic
components, these instructions must be
followed precisely.

If you are unsure about how to follow this
procedure, we strongly recommend that
you seek the help of a competent me-
chanic or towing service.

CAUTION

Batteries contain sulfuric acid
which is poisonous and corrosive.
Wear protective safety glasses when
jump starting, and avoid spilling
acid on your skin, clothing, or ve-
hicle.

If you should accidentally get acid
on yourself or in your eyes, remove
any contaminated clothing and flush
the affected area with water im-
mediately. Then get immediate medi-
cal attention. If possible, continue
to apply water with a sponge or
cloth while en route to the medical
office.

The gas normally produced by a
battery will explode if a flame or
spark is brought near. Use only
standardized jumper cables and do
not smoke or light a match while
jump starting.

NOTICE

The battery used for boosting must
be 12 V. Do not jump start unless you
are sure that the booster battery is
correct.

JUMP STARTING PROCEDURE

1. If the booster battery is installed in

another vehicle, make sure the vehicles
are not touching. Turn off all unneces-
sary lights and accessories.

When boosting, use the battery of
matching or higher quality. Any other
battery may be difficult to jump start
with.

If jump starting is difficult, charge the
battery for several minutes.

2. If required, remove all the vent plugs

from the booster and discharged batter-
ies. Lay a cloth over the open vents
on the batteries. (This helps reduce the
explosion hazard, personal injuries and
burns.)

3. If the engine in the vehicle with the

booster battery is not running, start it
and let it run for a few minutes. During
jump starting, run the engine at about
2000 rpm with the accelerator pedal
lightly depressed.

(c) Jump starting

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Jeda Wireless Pad Manual preview
Wireless Pad
Brand: Jeda Pages: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Brand: Jeep Pages: 496
Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Brand: Mazda Pages: 12
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Brand: Honda Pages: 85
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Brand: GMC Pages: 120
Prime Tech H-066 User Manual preview
H-066
Brand: Prime Tech Pages: 6
iOttie Aivo Connect Setup Manual preview
Aivo Connect
Brand: iOttie Pages: 58
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Brand: VER-MAC Pages: 64
Quadratec 16053.5300 Installation Manual preview
16053.5300
Brand: Quadratec Pages: 6
Oldsmobile 2003 Alero Owner'S Manual preview
2003 Alero
Brand: Oldsmobile Pages: 354
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Brand: ULTIMATE SPEED Pages: 40
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Brand: Mont Blanc Pages: 2
Skoda FABIA II TMB PS 035 Mounting And User Instructions preview
FABIA II TMB PS 035
Brand: Skoda Pages: 16
Autoplugin RCP-B1 Installation Manual preview
RCP-B1
Brand: Autoplugin Pages: 8

Brands by name

Popular brands

Load more brands