manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

278

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Keep your tire inflation pressures
at the proper level.

The recommended cold tire inflation
pressures, tire sizes and the com-
bined weight of occupants and cargo
(vehicle capacity weight) are de-
scribed on page 302 and 306. They
are also on the tire and loading infor-
mation label.

You should check the tire inflation
pressure every two weeks, or at least
once a month. And do not forget the
spare!

The following  instructions for
checking tire inflation pressure
should be observed:

The pressure should be
checked only when the tires are
cold. If your vehicle has been
parked for at least 3 hours and has
not been driven for more than 1.5
km or 1 mile since, you will get
an accurate cold tire inflation pres-
sure reading.

Always use a tire pressure
gauge. 

The appearance of a tire

can be misleading. Besides, tire
inflation pressures that are even
just a few pounds off can degrade
ride and handling.

Take special care when adding
air to the compact spare tire.
The smaller tire size can gain
pressure very quickly. Add com-
pressed air in small quantities and
check the pressure often until it
reaches the specified pressure.

Do not bleed or reduce tire
inflation pressure after driving.
It is normal for the tire inflation
pressure to be higher after driving.

Never exceed the vehicle capac-
ity weight. Passenger and lug-
gage weight should be located so
that the vehicle is balanced.

Checking tire inflation
pressure

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Brand: Panasonic Pages: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Brand: Panasonic Pages: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Brand: Panasonic Pages: 12
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Brand: Jeep Pages: 108
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Brand: BrandMotion Pages: 8
Whispbar K607W Fitting Instructions Manual preview
K607W
Brand: Whispbar Pages: 14
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Brand: E&G Classics Pages: 3
Volvo S90 2018 Quick Manual preview
S90 2018
Brand: Volvo Pages: 42
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Brand: Demco Pages: 4
Navman T1 F20 User Manual preview
T1 F20
Brand: Navman Pages: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Brand: Macrom Pages: 10
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Brand: Griffin Technology Pages: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Brand: Mitsubishi Pages: 919
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Brand: Seat Pages: 300
Menabo FROZEN ALU Fitting Instructions preview
FROZEN ALU
Brand: Menabo Pages: 4
Jaeger 21360505J Fitting Instructions Manual preview
21360505J
Brand: Jaeger Pages: 13
Mercedes-Benz G 55 AMG Operator'S Manual preview
G 55 AMG
Brand: Mercedes-Benz Pages: 284

Brands by name

Popular brands

Load more brands