manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

241

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

5. Position the tire edge against the

rear center end of the rear luggage
storage box lid. Then pull the ends
of the belts to secure the tire se-
curely.

After stowing the flat tire, check that
the tire and belts are secured.

To loosen the tire tie- down belts, see
“Tie- down hooks and tire tie- down
belts” on page 178 in Section 1- 10.

11. Check the air pressure of the re-

placed tire.

Adjust the air pressure to the specifi-
cation designated on page 306 in
Section 8. If the pressure is lower,
drive slowly to the nearest service
station and fill to the correct pressure.

Do not forget to reinstall the tire infla-
tion valve cap as dirt and moisture
could get into the valve core and
possibly cause air leakage. If the cap
is missing, have a new one put on as
soon as possible.

As soon after changing wheels as
possible, tighten the wheel nuts to the
torque specified on page 306 in Sec-
tion 8 with a torque wrench. Have a
technician repair the flat tire.

—After changing wheels

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

RACLET SAFARI Setup And Maintenance Manual preview
SAFARI
Brand: RACLET Pages: 48
RACLET Allegra Manual preview
Allegra
Brand: RACLET Pages: 31
Fab Fours BLACK STEEL S2560 Installation Instructions Manual preview
BLACK STEEL S2560
Brand: Fab Fours Pages: 9
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Brand: DEFA Pages: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Brand: rough country Pages: 8
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Brand: Victory 4x4 Pages: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Brand: Keith Pages: 2
Chevrolet LUMINA 1997 Owner'S Manual preview
LUMINA 1997
Brand: Chevrolet Pages: 376
Mazda 2008 CX-9 Brochure & Specs preview
2008 CX-9
Brand: Mazda Pages: 15
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Brand: Enduro Pages: 48
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Brand: ULTIMATE SPEED Pages: 6
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Brand: I.D. Systems Pages: 41
FALCON RIDGE HU-4421-XL-SDK01 Instructions For Installation And Care preview
HU-4421-XL-SDK01
Brand: FALCON RIDGE Pages: 5
FALCON RIDGE Bobcat 3400 Instructions For Installation And Care preview
Bobcat 3400
Brand: FALCON RIDGE Pages: 4
Club Car TransPorter 4 Maintenance And Service Manual preview
TransPorter 4
Brand: Club Car Pages: 286
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Brand: Havis-Shields Pages: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Brand: PEUGEOT Pages: 107
Westin 33-1920 Instructions preview
33-1920
Brand: Westin Pages: 3

Brands by name

Popular brands

Load more brands