manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

129

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

LOW TIRE PRESSURE WARNING LIGHT

This light comes on when the ignition key
is turned to the “ON” position. It goes off
after a few seconds. This indicates that
the tire pressure warning system is func-
tioning properly.

If the low tire pressure warning light
comes on or blinks while driving, do
the following.

If the warning light comes on:

1. Adjust the tire inflation pressure to

the specified level as soon as pos-
sible. (See “Tires” on page 306 in
Section 8.)

2. Push the tire pressure warning sys-

tem reset switch for a few seconds
and make sure the warning light
goes off.

If the light remains on after the reset
switch has been pushed, have the tire
pressure warning system checked at your
Toyota dealer.

If you have a flat tire, replace it with the
spare tire. For details, see “If you have
a flat tire” on page 231 in Section 4.

If the warning light blinks once every
second:

The low tire pressure warning system may
be malfunctioning. Contact your Toyota
dealer.

If the warning light blinks once every
three seconds:

The low tire pressure warning system
needs to be initialized. Reset the system
with the tire pressure warning system re-
set switch. (To reset the system, see
“TIRE PRESSURE WARNING SYSTEM
RESET SWITCH”.)

The tire pressure warning system does
not function properly under certain cir-
cumstances. In the following cases, the
low tire pressure warning light may not
come on even if the tire inflation pres-
sure is low, or it may come on when
the tire inflation pressure is actually
normal.

A compact spare tire, snow tires, or
tire chains are used.

The tire inflation pressure is excessive-
ly higher than specified, or tire inflation
pressure suddenly drops due to burst-
ing or other causes.

The vehicle is driven on a slippery
road surface such as rough or frozen
roads.

The vehicle speed is less than 30 km/h
(19 mph) or more than 100 km/h (62
mph), and the driving duration is less
than 5 minutes.

The tires differ in tread pattern or
manufacturer.

The tires are not the specified size.

The tread wear is very different among
the installed tires.

Rapid acceleration/deceleration or
sharp turns is continued.

Towing a trailer.

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Brand: Panasonic Pages: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Brand: Panasonic Pages: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Brand: Panasonic Pages: 12
Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Brand: Jeep Pages: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Brand: Jeep Pages: 80
Saab B205 Installation Instructions Manual preview
B205
Brand: Saab Pages: 10
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Brand: Safe Fleet Pages: 12
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Brand: Saleen Pages: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Brand: Buick Pages: 5
Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
Cequent 10417 Instruction Sheets preview
10417
Brand: Cequent Pages: 9
Porsche 911 GT3 - Owner'S Manual preview
911 GT3 -
Brand: Porsche Pages: 195
PEUGEOT Partner Origin Handbook preview
Partner Origin
Brand: PEUGEOT Pages: 128
Schumacher Electric SPI6 Owner'S Manual preview
SPI6
Brand: Schumacher Electric Pages: 87
Cadillac 2009 ESCALADE ESV Owner'S Manual preview
2009 ESCALADE ESV
Brand: Cadillac Pages: 602
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5

Brands by name

Popular brands

Load more brands