manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

235

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

3. Remove the wheel ornament.

Pry off the wheel ornament, using the
beveled end of the wheel nut wrench
as shown.

CAUTION

Do not try to pull off the orna-
ment by hand. Take due care in
handling the ornament to avoid
unexpected personal injury.

4. Loosen all the wheel nuts.

Always loosen the wheel nuts before
raising the vehicle.

Turn the wheel nuts counterclockwise
to loosen. To get  maximum leverage,
fit the wrench to the nut so that the
handle is on the right side, as shown
above. Grab the wrench near the end
of the handle and pull up on the han-
dle. Be careful that the wrench does
not slip off the nut.

Do not remove the nuts yet—just un-
screw them about one- half turn.

CAUTION

Never use oil or grease on the
bolts or nuts. The nuts may loose
and the wheels may fall off,
which could cause a serious ac-
cident.

—Removing wheel ornament
(steel wheels)

—Loosening wheel nuts

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Daihatsu S85 Wiring Diagrams preview
S85
Brand: Daihatsu Pages: 41
Daihatsu S85 Workshop Manual preview
S85
Brand: Daihatsu Pages: 268
Triumph MAYFLOWER 1951 Instruction Book preview
MAYFLOWER 1951
Brand: Triumph Pages: 86
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Brand: RAM Pages: 16
Paxton Automotive Novi Owner'S Installation Manual preview
Novi
Brand: Paxton Automotive Pages: 85
Thule 1489 Instructions Manual preview
1489
Brand: Thule Pages: 8
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Brand: Monacor Pages: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Brand: Jeep Pages: 338
Pacbrake C44059 Installation Manual preview
C44059
Brand: Pacbrake Pages: 14
Whispbar K919W Fitting Instructions Manual preview
K919W
Brand: Whispbar Pages: 17
DriveRight 8156OBD Installation Manual preview
8156OBD
Brand: DriveRight Pages: 16
MAcarbon MAA.R8.06 Install Instructions preview
MAA.R8.06
Brand: MAcarbon Pages: 3
Saab 32 025 907 Installation Instructions Manual preview
32 025 907
Brand: Saab Pages: 37
Hyundai 2001 Elantra Owner'S Manual preview
2001 Elantra
Brand: Hyundai Pages: 168
Honda 2000 RL Owner'S Manual preview
2000 RL
Brand: Honda Pages: 330
Edelbrock PRO-FLO XT 3527 User Manual preview
PRO-FLO XT 3527
Brand: Edelbrock Pages: 39
Flash Cover MN012 Installation Manual preview
MN012
Brand: Flash Cover Pages: 2
Buick Riviera 1967 Owner'S Manual preview
Riviera 1967
Brand: Buick Pages: 58

Brands by name

Popular brands

Load more brands