manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

244

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

(a) Towing with wheel lift type truck—

(b) Using flat bed truck

—From rear

—From front

Four- wheel drive models

If towing is necessary, we recommend
you to have it done by your Toyota
dealer or a commercial tow truck ser-
vice. In consultation with them, have
your vehicle towed using either (a) or
(b).

Only when you cannot receive a towing
service from a Toyota dealer or com-
mercial tow truck service, tow your ve-
hicle carefully in accordance with the
instructions given in “—Emergency tow-
ing” on page 246 in this Section.

Proper equipment will help ensure that
your vehicle is not damaged while being
towed. Commercial operators are generally
aware of the state/provincial and local
laws pertaining to towing.

Your vehicle can be damaged if it is
towed incorrectly. Although most operators
know the correct procedure, it is possible
to make a mistake. To avoid damage to
your vehicle, make sure the following pre-
cautions are observed. If necessary, show
this page to the tow truck driver.

NOTICE

Four- wheel drive models—When tow-
ing, be sure to tow the vehicle with
all four wheels lifted. Otherwise, the
drive system could be damaged and
the vehicle could fly off the tow
truck.

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

RAM 2500 2020 Quick Reference Manual preview
2500 2020
Brand: RAM Pages: 20
Pivot DXB-B User Manual preview
DXB-B
Brand: Pivot Pages: 4
Bestop 54822 Installation Instructions Manual preview
54822
Brand: Bestop Pages: 11
Whispbar K455W Fitting Instructions Manual preview
K455W
Brand: Whispbar Pages: 14
Vauxhall 2014 Insignia VXR SuperSport Specifications preview
2014 Insignia VXR SuperSport
Brand: Vauxhall Pages: 56
Audi 2011 A3 Sportback Pricing And Specification Manual preview
2011 A3 Sportback
Brand: Audi Pages: 29
Prorack WHISPBAR S53 Fitting Instructions For Basic Carrier preview
WHISPBAR S53
Brand: Prorack Pages: 10
Mitsubishi MOTORS PAJERO SPORT Manual preview
PAJERO SPORT
Brand: Mitsubishi MOTORS Pages: 416
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Brand: TEINHOF Pages: 2
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Brand: Oldsmobile Pages: 380
Club Car TransPorter 4 Maintenance And Service Manual preview
TransPorter 4
Brand: Club Car Pages: 286
Pontiac 2007 G6 Owner'S Manual preview
2007 G6
Brand: Pontiac Pages: 486
Thule 953000 Instructions Manual preview
953000
Brand: Thule Pages: 8
Waeco MagicSafe MSG150 Installation And Operating Manua preview
MagicSafe MSG150
Brand: Waeco Pages: 20
Lund Tonno Pro Installation Instructions Manual preview
Tonno Pro
Brand: Lund Pages: 12
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Brand: Federal Signal Corporation Pages: 20
MacNeil Pet Barrier Instruction Manual preview
Pet Barrier
Brand: MacNeil Pages: 2
AUTOTECH 10.297.300K-303K Installation Instructions preview
10.297.300K-303K
Brand: AUTOTECH Pages: 1

Brands by name

Popular brands

Load more brands