Toyota AVALON 2005 Operating Manual Download Page 71 | Manualshive

Page: 71 / 319

background image

’05 MATRIX_U (L/O 0409)

71

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Child restraint systems are classified into
the following 3 types depending on the
child’s age and size.

(A) Infant seat
(B) Convertible seat
(C) Booster seat

Install the child restraint system following
the instructions provided by its manufac-
turer.

Your vehicle has anchor brackets for se-
curing the top strap of a child restraint
system.

For instructions about how to use the an-
chor bracket, see “—Using a top strap” on
page 82 in this Section.

The child restraint lower anchorages ap-
proved for your vehicle may also be used.
See “—Installation with child restraint low-
er anchorages” on page 84 in this Sec-
tion.

(A) Infant seat

(B) Convertible seat

(C) Booster seat

—Types of child restraint
system

«
...
69
70
71
72
73
...
»

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: Kia Pages: 385

Ride-Rite Air Helper Springs 2173

Brand: Firestone Pages: 4

Brand: ULTIMATE SPEED Pages: 50

Brand: Quadratec Pages: 12

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: MAcarbon Pages: 3

Brand: Brink Pages: 26

Brand: Renault Pages: 198

Dynamic Power Management Home - Module

Brand: newmotion Pages: 20

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Brand: Suzuki Pages: 504

Brand: Scosche Pages: 8

Brand: Kuda-Phonebase Pages: 3

Brand: Honda Pages: 330

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands